ClearOne PSR1212 Spezifikationen Seite 9
- Seite / 172
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
TECHNICAL SUPPORT: 1.800.283.5936 (USA) OR 1.801.974.3760
INSTALLATION AND SETUP • REAR PANEL
5
Rear Panel
1
. Power This power module (see Figures 2 and 3) accommodates power
ranging from 100–240VAC, 50/60Hz. The module uses an IEC-type
connector. No switching is required.
2.
Inputs 1-8 This bank of Phoenix™ block connectors (see Figures 2 and
4) is for connection of eight mic-level or line-level (selectable) inputs. This
bank of connectors is typically used for mics, but can be configured for
use with VCRs, CD players, etc. These inputs can be mixed in any gated or
non-gated combination and routed to any of the 12 outputs. Default input
level is -55dBu. For more information about input adjustments, see page
36. For electrical specifications, see Appendix A: Specifications.
3.
RS-485 Remote Panel A/B Port These four-pin Phoenix connector ports
(see Figures 2 and 5) allow you to control the PSR1212 with the Gentner
Control Panel.
Power is supplied through the RS-485 ports to the remote control devices
from the PSR1212. This power is limited to a total of 300mA at 15 volts for
each connector. Over-current protection is provided on the +15V pins to
prevent damage in the event of shorting. External power can be provided
to control devices when more current is required. See page 86 for
maximum cable run distances when using Gentner Control Panels.
4. Control/Status P
orts A and B These two female DB25 connectors (see
Figures 2 and 6) are for connecting control devices to the PSR1212. The
control devices have access to the command set for the PSR1212 and can
be used for common functions such as volume control, muting, preset
change, room combining, etc. Devices can be connected to either port.
For instructions on how to program the control and status pins, see the
GPIO section on page 59. The default settings allow control and status of
inputs, outputs, volume, and presets. These pins are active low. The 32
presets can also be activated via these connectors. For pinout and default
information, see Appendix B.
5.
Outputs 1-12 These three-pin Phoenix connectors (see Figures 2, 7, and
8) is for connection of eight line-level balanced outputs with three-pin
Phoenix connectors. These outputs are typically used for connection to
1
5
2
5
6
7 8
9
4
3
Expansion Bus
In
Out
Figure 2. Rear Panel
Figure 3. Power Plug
Figure 4. Inputs 1-8
Figure 5. RS-485 Remote Panel A/B Ports
Figure 6. Control/Status Ports A and B
13
25
1
14
- Digital Matrix Mixer with 1
- Audio Processing 1
- Gentner Part No. 800-155-001 2
- June 2001 (Rev. 4.0) 2
- TABLE OF CONTENTS 4
- Introduction 5
- INTRODUCTION • OVERVIEW 6
- Installation and Setup 7
- Front Panel 8
- Rear Panel 9
- Expansion Bus 10
- Installation 11
- First PSR1212 Second PSR1212 12
- Third PSR1212 12
- LCD Programming 14
- System-Level LCD Parameters 15
- RS-232-Level LCD Parameters 17
- Meter-Level LCD Parameters 18
- Meter Reference Point Diagram 19
- Operation 20
- PSR1212 G-Ware 21
- Software 21
- Procedure 22
- Select Program Folder Window 23
- G-Ware Software 24
- Configuration 24
- Create New Site 25
- Change File Password Windows 26
- Adding a PSR1212 27
- Unit to a Site 27
- G-WARE SOFTWARE • SECURITY 28
- G-Ware Flow Screen 29
- Pull-Down Menus 30
- Units Menu 31
- Tools Menu 32
- Help Menu 32
- Connect Menu 32
- Toolbar Buttons 33
- Message Log Button 37
- Compare Utility Button 37
- G-Ware Matrix 38
- Cross Point Attenuation 39
- Matrix Report 40
- Inputs 1-8 Configuration 40
- G-WARE SOFTWARE • INPUTS 1-8 41
- G-WARE SOFTWARE • FILTERS 42
- Input 1 Configuration 44
- Gate Configuration Window 44
- ▲/▼buttons or by 45
- Gating Group Select Pane 46
- Mic 1 Configuration 47
- Copy Menu 47
- Inputs 9-12 Configuration 48
- From Expansion Bus Labeling 49
- From Processing Configuration 50
- Compressor Setup Window 51
- Processing Filters Window 52
- Delay Window 54
- Outputs 1-12 Configuration 56
- To Expansion Bus Labels 57
- To Processing Configuration 57
- Advanced Operation 59
- Preset Configuration Pane 60
- Preset Macros Window 62
- Preset GPIO Builder Window 63
- Control Panel Builder Window 64
- Macro Mode 65
- G-Ware Macro Window 66
- Macro Editor Button 67
- Macro Editor Window 67
- Macro Name Window 67
- Gate View 68
- Meter Views 69
- Signal Generator Window 70
- Gentner G-Ware Menu (Windows 71
- Compare Utility Window 1 71
- G-Ware Open Window 72
- Print Preview Window 72
- Copy to Site 1 Button 73
- Document Compare Window 2 73
- Application Example 75
- Hotel/Convention Center 76
- Pin Assignment for Preset 1 77
- Room-Combining Scenarios 78
- Pin Assignment for Preset 2 78
- Pin Assignment for Preset 4 79
- Pin Assignment for Preset 5 79
- Pin Assignment for Preset 3 79
- Pin Assignment for Preset 6 80
- Appendices 83
- APPENDIX A • SPECIFICATIONS 84
- Appendix B: 85
- Connector Pinouts 85
- Control/Status Ports A, B 86
- RS-485 Remote Control Ports 87
- Preset Setup 88
- Room Configuration Setup 88
- Appendix C: Control 89
- Panel Installation 89
- Appendix D: 91
- Accessories 91
- Appendix E: Serial 91
- Port Commands 91
- PSR1212 Serial Commands 92
- Adaptive Ambient Mode 99
- Ambient Level Adjust 100
- Automatic Gain Control 101
- Baud Rate 102
- Chairman Override Mode 103
- Compression Select 104
- Compressor Adjust 105
- Compressor Group Select 106
- Decay Adjust 107
- Delay Select 108
- Default Meter 109
- Delay Adjust 110
- Device ID 111
- Expansion Bus Reference 112
- APPENDIX E • SERIAL COMMANDS 113
- Filter Select 116
- First Mic Priority Mode 117
- Flow Control 118
- Front Panel passcode 119
- Gain Adjustment 120
- Gate Hold Time Adjust 121
- Gate Status 122
- Gate Ratio Adjust 123
- Gate Reporting 124
- Gating Group 125
- Gating Mode 126
- Gating Override 127
- Last Mic On Mode 129
- Level Report 132
- RETURN VALUES 133
- If Command Returns 133
- Level Report Rate 134
- Lock Front Panel 135
- Macro Execution/Reporting 136
- Matrix Attenuation Adjust 139
- Maximum Gain Setting 140
- Maximum Number of Microphones 141
- Mic/Line Adjust 142
- Minimum Gain Setting 143
- Modem Initialization String 144
- Modem Mode 145
- Modem Password 146
- Off Attenuation Mode 149
- PA Adaptive Mode 150
- PA Reference Select 151
- Phantom Power 152
- Preset Execution/Reporting 153
- Program String 154
- Serial Echo 155
- Serial Mode 156
- Signal Generator 157
- String Execution 158
- Time Out Select 159
- Glossary 163
- GLOSSARY 164
- Warranty 169
- Compliance, and 169
- Safety Information 169
- FCC Part 15 Compliance 170
Verwandte Produkte und Handbücher für Audio-Equalizer ClearOne PSR1212
Audio-Equalizer ClearOne XAP 800 Spezifikationen
(152 Seiten)
(152 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.118 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern